Re: [IRCA] New receiver ground
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [IRCA] New receiver ground



On my ground rod I dug a hole 5 feet deep with a shovel and a 5 foot steel bar and used a shop-vac to get the dirt out of the hole when the shovel would not work any more.  I than used a large hammer to pound the copper pipe in the last 5 feet but had to stop at 4 feet as I hit a rock.  I than put in 30 lbs of salt with lots of water over the next 2 days.  Than I used 30 lbs of Bentonite to fill the hole.  
 
Bill Block
Prescott Valey, AZ> From: mwdxer@xxxxxxxxx> Date: Fri, 10 Aug 2007 19:30:17 -0700> To: irca@xxxxxxxxxxxxxxxx; am@xxxxxxxxxxx> Subject: [IRCA] New receiver ground> > Hi everyone,> > After I read about Bill Block's addition of a new 10 foot piece of> copper pipe pounded into the ground for his receiver there in Prescott> Valley AZ, this morning I stopped by a lumberyard in Gearhart (near> Seaside), and picked up one 10 foot piece of copper pipe like I have> been installing for the EWE and beverage antennas. But in those cases I> would cut the piping in two pieces, fiquring with how wet the soil is> here, a series of 5 foot copper pipes would be plenty. After all the> yard is loaded with copper piping as I have been installing more and> more. But one ground I have not made a change in since I moved in out> here was the receiver ground. The single 5 foot copperclad Radio Shack> rod was in the ground under the house. Lightening is very rare here, so> I never was concerned anyway. So, I thought, I should install something> better than that for the receivers. I have all three (R8, SPR4, and> R1000) tied to the one single 5 foot rod for well over 20 years. Well, I> thought, why not put the whole 10 foot copper pipe in the ground instead> of cutting in two. I found a soft spot about a foot from where the old> one is and pushed the 10 foot rod into the ground maybe 18 inches. I> then got the ladder out and climbed up and started to pound the 10 foot> section strainght into the ground. It took some effort, but 20 minutes> later only 2 inches stuck out. Fortunally no big tree roots or rocks.> The question everyone is asking, was it worth the effort? Probably not,> but it did made a slight difference in the noise level. You can hear it> with your ear by disconnecting the new ground leaving the old one, but> will it make any difference DXwise? I kind of doubt it, but who knows?> But at least that ground to the receivers is a good one now.. I think I> have come to the end as any more ground rods I add will make little> difference here, with our wet soil. And my arms are getting tired. hi.> > 73,> > Patrick> > Patrick Martin> KAVT Reception Manager> > _______________________________________________> IRCA mailing list> IRCA@xxxxxxxxxxxxxxxx> http://montreal.kotalampi.com/mailman/listinfo/irca> > Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers> > For more information: http://www.ircaonline.org> > To Post a message: irca@xxxxxxxxxxxxxxxx> 
_________________________________________________________________
Find a local pizza place, movie theater, and more….then map the best route!
http://maps.live.com/default.aspx?v=2&ss=yp.bars~yp.pizza~yp.movie%20theater&cp=42.358996~-71.056691&style=r&lvl=13&tilt=-90&dir=0&alt=-1000&scene=950607&encType=1&FORM=MGAC01
_______________________________________________
IRCA mailing list
IRCA@xxxxxxxxxxxxxxxx
http://montreal.kotalampi.com/mailman/listinfo/irca

Opinions expressed in messages on this mailing list are those of the original contributors and do not necessarily reflect the opinion of the IRCA, its editors, publishing staff, or officers

For more information: http://www.ircaonline.org

To Post a message: irca@xxxxxxxxxxxxxxxx